0
  • No products in the cart.
Total:$0

Carbide Base Audio Isolation Feet

Carbide Base Audio Isolation Feet

Vibrations induced from loudspeakers can turn the surfaces of a room into unwanted sound radiating sources. Vibrations can also induce noise in the output of sensitive electronics such as turntables due to the phenomenon of microphony. The patent pending design of our Carbide Base audio isolation feet isolates these vibrations in all directions when placed under your audio electronics and loudspeakers.

 

It is also important to reduce the magnitude of stray vibrations and dissipate them over time. Specially formulated viscoelastic materials with high loss factors remove over 65% of incoming vibration energy through a conversion into heat. Undesired resonances are subdued.

Multi-Axis Audio Isolation Feet

Separate upper and lower portions are designed to optimize vibration isolation and dissipation in vertical and horizontal directions.

 

The upper portion is machined out of aluminum billet to accept a specially formulated viscoelastic member called ViscoRing™. The ViscoRing™ acts as a damped spring supporting the equipment while isolating it from vertically oriented vibrations. It is replaceable depending on the intended supporting weight range.

 

The lower portion comprises separate machined stainless steel sections. 18 exceptionally tough zirconia ball bearings and 3 viscoelastic elements are incorporated to enhance horizontal isolation and damping. The bottom is threaded to facilitate nearly 3/4″ (20 mm) of height adjustment. It can also optionally accept the 3 provided spikes to pierce through carpet.

Low Shape Factor

When it comes to viscoelastic materials providing isolation, more is not necessarily better. It is the low ratio of surface area supporting weight to the surface area free to bulge outward which is important. The term for this ratio is Shape Factor. The lower the Shape Factor, the greater the potential degree of isolation.

 

Carbide Base audio isolation feet implement viscoelastic materials with Shape Factors far lower than previous designs. The large tubular shape of the ViscoRing™ maximizes the surface area that is free to bulge. This yields a Shape Factor around half of the lower limit traditionally used for elastomer isolators. The low shape factor is made possible by the patent pending design of the Carbide Base footer. Ridges selectively brace the ViscoRing™ to stabilize it under compression and shear while leaving a substantial surface area free to bulge.

Universal Stud System

Carbide Base footers can be optionally mounted to equipment and loudspeakers with the supplied screws in metric thread sizes M4, M6, M8, M10 and imperial sizes #8-32, 1/4″-20, 3/8″-16, 1/2″-13. The screws are standard flat head machine screws allowing easy substitution for a different thread size or length. A removable nylon insert is provided for smaller diameter screws.

 

A machined stainless steel jam bolt is provided to thread in behind the screw to secure it in place. The jam bolt has a top threaded hole to hold one of the included spikes to rigidly couple to the underside of equipment. The jam bolt can also be removed to provide a cavity to captively hold a loudspeaker floor spike.

  • "Bass cleaned up even more, my small knots of structural striations vanished and floor-borne involvement felt eradicated. On a good day I'd expected that, just not this much. What came as a shock? The entire system's noise floor seemed to have fallen."

    Srajan Ebaen - 6moons.com

  • "Carbide Bases not only turned my DAC into a gutsier and rounder version of itself, but also faster and dynamically more gifted on top of that. This sensibly more elastic, orderly and optically grander outcome was quite the surprise for me."

    Dawid Grzyb - HiFiKnights.com

ViscoRings™

All Carbide Base footers are the same size. Each is optimized for the weight of your equipment by choosing among the 4 available interchangeable ViscoRings™. The recommended supporting weight range with each ViscoRing™ installed is shown below.

 

While some isolation devices require different versions for different weights, a single version of the Carbide Base footer can support a wide range of equipment weights by simply replacing the installed ViscoRing™.

Transmissibility

Transmissibility is the ratio of vibration energy transmitted into one side of a Carbide Base footer (such as from a loudspeaker) to what is being applied to the other side (such as the floor). A transmissibility less than 1 is represents vibration isolation which is desired. Anything greater than 1 is an amplification of vibrations.

 

Most passive vibration isolators exhibit an amplification of vibrations at frequencies near the resonance frequency of the device. The unique design of the Carbide Base footer minimizes this amplification and confines it to frequencies around the lower threshold of human hearing. Low frequencies are important to isolate as they travel with little impedance throughout the room and equipment as structure-borne vibrations.

Loss Factor

Loss factor, or tangent delta, is a measure how much vibration energy is dissipated through a conversion to heat due to the phenomenon of hysteresis. A loss factor of 0 indicates a perfectly elastic material where the oscillating force of a vibration occurs in-phase (at the same time) with the accompanying deformation of the material. A loss factor of 1 indicates a perfectly viscous material where the force and deformation are exactly 90 degrees out of phase resulting in total dissipation of vibration energy to heat.

 

The viscoelastic materials utilized in Carbide Base footers are engineered to have an exceptionally high loss factor over a wide frequency range. The gray ViscoRing™ has the highest loss factor, followed closely by the blue, black, and red ViscoRings™ which can support incrementally higher weights. For reference, natural rubber has a loss factor of about 0.05 across most audible frequencies.

The vibration dissipation ability of a Carbide Base footer is significant enough to measurably subdue resonances in equipment being supported. The graphs below show low frequency vibrations in the panels of a test loudspeaker enclosure as measured using a calibrated accelerometer. Dips and spikes in panel acceleration indicating resonances are effectively damped when the same measurement is taken with Carbide Base footers placed under the loudspeaker.

Loudspeaker Bottom Panel
Loudspeaker Upper Side Panel

Loudspeaker panel acceleration measured with a ACH-01 sensor, 10 dB gain, using 35 to 150 Hz log swept sine excitation. The measurements on Carbide Base footers are shown in blue. The measurements on floor spikes directly on the concrete floor are shown in red. See the Vibration Dissipation Measurements for details.

Dimensions

Instructions

Installing ViscoRings™

1 Insert supplied 2.5mm Allen wrench down into each of the 3 holes on the top pad and unscrew the bolts housed within. Note: Once fully unscrewed the bolts will remain retained under the pad.

2 Pry apart the upper and lower portions to access the installed ViscoRing™. Be patient prying apart as the ViscoRing™ can become tacky and slow to separate. The bottom portion can be partially unthreaded to increase prying leverage.

 

3 Replace the ViscoRing™. Ensure that the new ViscoRing™ is fully seated into the underside of the upper portion. Store the unused ViscoRing™ in a safe place. It is normal for newly installed ViscoRings™ to settle and compress slightly after an initial period of use.

4 Align the top holes on the upper portion with the thread holes on top of the lower portion. Press the upper portion down over the top of the lower portion.

 

5 Insert the Allen wrench into the top holes and tighten the bolts housed within. The bolt will stop turning when fully secured. Do not overtighten. Pressing down and lightly twisting the upper portion can help guide the bolts into their holes. If the bolts still do not align with their holes, remove the upper portion and try again.

6 (Optional) Unthread the bottom section as needed to increase the height of the Carbide Base< footer to level uneven loads.

FAQ

– What separates Carbide Base footers from the competition?

We believe there are 3 primary advantages of Carbide Base footers over the competition:

  1. Low resonance frequency in all directions – An exceptionally wide bandwidth of vibration isolation means that nearly all of the audible frequency range is isolated. This includes the lowest frequencies most likely to excite room surfaces. Many devices provide limited isolation bandwidth or are effective only in certain directions.
  2. High loss factor – Specially formulated viscoelastic materials convert over 65% of vibration energy into heat to effectively damp resonances. Vibration dissipation is higher than many other devices utilizing vibration transmission-path evasion methods or inferior elastomer materials.
  3. Wide supporting weight range – Interchangeable ViscoRings™ allow a single device to effectively isolate a wide range of equipment weights. Some other competitors require purchasing different versions of their devices to support different equipment ranges.
– Carbide Base footers didn’t work out for me. Can I return them?

Yes. We encourage new owners to give plenty of time to adjust to the differences introduced by our Carbide Base footers. If you are still not happy with the results simply return your item within 60 days to receive a refund. US domestic orders include a return shipping label to simplify this for you. See our Return Policy for details.

– Should I use fewer Carbide Base footers with heavier ViscoRings™, or more with lighter ViscoRings™?

More Carbide Base footers with lighter ViscoRings™ will typically outperform fewer with heavier ViscoRings™ due to increased damping. However, low frequency isolation will be best when ViscoRings™ are used on the high end of their recommended weights. This might require using just 3 Carbide Base footers under lighter equipment. Equipment weighing under about 22 lbs (10 kg) will typically perform better with 3 Carbide Base footers with Light ViscoRings™.

– Do you ship internationally?

Yes. Click Add to Cart and specify your shipping address to get a real time shipping quote. Import duties and taxes are collected up front at the time of checkout to simplify customs clearance and to ensure that you are not responsible for any additional fees upon delivery. See our Shipping Policy for details.

– I heard anchoring is important in audio. Why do you claim allowing movement is good for isolation?

To provide isolation, out-of-phase movement must be allowed. If a manufacturer claims that their product “anchors” below a certain frequency or in certain directions it means that isolation is compromised in these situations. While Carbide Base footers allow movement to achieve isolation, the high level of damping works to significantly subdue the magnitude and duration of these movements. Carbide Base footers settle quickly following the impulse of a vibration.

 

Below the transition frequency (typically around 200 Hz) the room becomes the dominant contributor to the listening experience in this region. Isolation of low frequencies is therefore critical. This is to minimize the storage into and subsequent delayed release of audible vibration energy from the surfaces of the room which can smear the bass and color the sound.